Teh Snorkler
- lll
- Middle Manager
- Posts: 1706
- Joined: Tue Jul 06, 2021 10:17 pm
- Has thanked: 998 times
- Been thanked: 937 times
Re: Teh Snorkler
"Teh Snorkler" ?
Is this some sort of male enhancement machine?
Asking for a friend...
Is this some sort of male enhancement machine?
Asking for a friend...
The Democratic Party is a criminal organization and the enemy within of the United States of America.
- PLX
- Executive
- Posts: 4148
- Joined: Wed Jul 14, 2021 10:46 pm
- Location: Bandera, TX
- Has thanked: 1407 times
- Been thanked: 1806 times
- PLX
- Executive
- Posts: 4148
- Joined: Wed Jul 14, 2021 10:46 pm
- Location: Bandera, TX
- Has thanked: 1407 times
- Been thanked: 1806 times
- PLX
- Executive
- Posts: 4148
- Joined: Wed Jul 14, 2021 10:46 pm
- Location: Bandera, TX
- Has thanked: 1407 times
- Been thanked: 1806 times
- harddriver
- Grand Poobah
- Posts: 5310
- Joined: Mon Jul 05, 2021 5:03 pm
- Has thanked: 588 times
- Been thanked: 1761 times
- PLX
- Executive
- Posts: 4148
- Joined: Wed Jul 14, 2021 10:46 pm
- Location: Bandera, TX
- Has thanked: 1407 times
- Been thanked: 1806 times
Re: Teh Snorkler
Naw, I just harvested all the parts from the previous pre-amp build, cleaned the board and started the layout.harddriver wrote: ↑Tue Nov 29, 2022 2:03 am Did you drill and stake a new turret layout specifically for the Snork build?
I've had to drill a couple of new holes so far, but it's going well.
Since I'm only using two 12AX7's I should have plenty of room. Trying to be as efficient as possible though.
- PLX
- Executive
- Posts: 4148
- Joined: Wed Jul 14, 2021 10:46 pm
- Location: Bandera, TX
- Has thanked: 1407 times
- Been thanked: 1806 times
- harddriver
- Grand Poobah
- Posts: 5310
- Joined: Mon Jul 05, 2021 5:03 pm
- Has thanked: 588 times
- Been thanked: 1761 times
Re: Teh Snorkler
I sent you 3 Evox/RIfa's if I remember correctly? No? They should all be in this build! IMHO for the WIMA Boggy sound!
How did you extend the Evox/RIfa leads?
NICE........................Board's looking good! Your lead dress is looking very neat and orderly!
Can't wait to hear this thing and whole lotta AIC riffs!
- PLX
- Executive
- Posts: 4148
- Joined: Wed Jul 14, 2021 10:46 pm
- Location: Bandera, TX
- Has thanked: 1407 times
- Been thanked: 1806 times
Re: Teh Snorkler
Yes. The.68µF caps were the only components I am able to use in this circuit.harddriver wrote: ↑Tue Nov 29, 2022 5:16 pm I sent you 3 Evox/RIfa's if I remember correctly? No? They should all be in this build! IMHO for the WIMA Boggy sound!
NICE........................Board's looking good! Your lead dress is looking very neat and orderly!
Can't wait to hear this thing and whole lotta AIC riffs!
The Wima caps will be delivered later this week.
If I'm not happy with the tone, I will try rolling different 12AX7 tubes in/out, then perhaps try swapping out some caps.
I just used bits of leads that I had trimmed off other components.. Bent a little hook into one end, crimped onto the leads of the box cap using a very small pair of needle-nose pliers and then applied a drop of hot solder.
- Ritchie's Party Hat
- Office Gopher
- Posts: 469
- Joined: Sun Jul 04, 2021 6:37 pm
- Has thanked: 294 times
- Been thanked: 279 times
Re: Teh Snorkler
Right. This is for Nuno-tone, right?
"You raise the blade, you make the change"
"Fritter and waste the hours in an offhand way"
Pink Floyd
"Fritter and waste the hours in an offhand way"
Pink Floyd
Who is online
Users browsing this forum: No registered users and 0 guests